Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI System Hardware & BigC Manual do Utilizador descarregar pdf (Página 104)

BigStuff3 Pro SEFI System

Version 2.1 – February 2011 96

Release the left mouse button. The screen below will open. Left Click on the “Pick Dash” drop down

screen.

The screen below will appear.

Pick Dash

drop down

screen

1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 137 138

BigComm Software 1
User Instruction Manual 1
Table of Contents 2
Table of Contents Continued 3
1. Introduction 3
Firewall grommet 7
MUST BOTH be 8
The vehicle 9
BigStuff3 Pro SEFI System 10
Fuel Pump 13
Ignition Systems Setup 18
Connector Clip 19
Connector Pin-out Identifier 23
Minimum 26
TPS, RPM 26
Parameters 26
Using the Brake Pedal Switch 27
Connector) 32
7. ECU Installation 34
8. BigComm Software Overview 35
11. Using the Tool Bar 41
BigComm 42
13. BigComm Main Menu Screen 45
“Enter” 45
For setup detail go to 49
Coil-on-Plug (COP) 49
Crank_Trigger_Configur 49
TPS Signal in the Dash 50
s)] to be used 51
 seconds) 51
 Ford Mod Motors: 329 52
20. Load vs. RPM 56
 Dwell Time Table 57
21. Firing Order 59
22. Injector Opening Time 59
23. Injector Phase Angle 60
25. Air Fuel Ratio Table 62
Cell Values Selected in a Row 63
14 14 13.5 13.8 63
14 13.9 13.8 13.8 63
26. Positive 02 Correction 66
27. Negative 02 Correction 67
30. SPARK (F4 – “Quick Key”) 69
31. Spark Table 69
32. FUEL (F3 – “Quick Key”) 72
33. Fuel Table 73
Enter” to save the change 74
34. STARTING 76
 Cranking 77
 After Start Delay 77
 After Start Decay 77
36. AfterStart Delay 78
37. AfterStart Correction 78
38. AfterStart Decay 79
39. Idle 80
40. Throttle Follower 80
41. Desired Idle RPM 81
42. Idle Spark 81
43. IAC Start Position 82
44. IAC Gain Terms 83
45. Warm Up 86
48. TRANSIENT FUEL 88
51. MAP AE Decay Rate 90
52. MAP AE Inc Rate 91
53. Run Time Correction 91
54. dMAP Parameters 92
55. Accel Pump Shot 94
56. AE Position Correction 94
57. Individual Cylinder 95
61. Boost Parameters 98
62. Boost PWM 99
63. Boost Staged 100
Switched 101
“Enter” to save the change 102
65. Dash 103
66. Configure Dash 103
67. Save a Dash 106
68. Load From File 107
69. Save to File 108
71. Logging (External) 109
72. Configure Log 110
74. View Log from File 111
Feature 115
77. Configure Replay 116
78. Upload Replay 117
79. View Replay from File 118
 SR2 with ETM 119
 NTK WBO2 for methanol 119
 CAN EGT 119
Blue Ellipse represents the 122
Set Default Calibration 125
83. Load a Calibration 126
84. Acronym Definition 127
85. Control Keys 127
86. Function or “Quick Keys” 128

Comentários a estes Manuais

Sem comentários

Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI System Hardware & BigC Manual do Utilizador Página 104

Comentários a estes Manuais

Manuais e produtos relacionados com Para o carro Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI System Hardware & BigC